| 单词 | crusher | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 释义 | crushercrushC0778100 (krŭsh)These verbs mean to press forcefully so as to reduce to a pulpy mass: crushed the rose geranium leaves; mashed the sweet potatoes; smashed the bamboo stems with a hammer; squashed the wine grapes. See Also Synonyms at crowd1.
crushercrumb-crunchercrumb-crushercrumb-cruncherand crumb-crushercrumb-crusherverbCrushercrusher,machine used to reduce materials such as ore, coal, stone, and slag to particle sizes that are convenient for their intended uses. Crushers operate by slowly applying a large force to the material to be reduced. Generally this is accomplished by catching it between jaws or rollers that move or turn together with great force. Reduction in size is generally accomplished in several stages, as there are practical limitations on the ratio of size reduction through a single stage.Crushera machine for crushing hard materials, chiefly mineral raw materials. A distinction is made between primary crushing (up to 100-300 mm), secondary crushing (25-100 mm) and pulverization (5-25 mm). Crushers are divided into five classes depending on the shape of the crushing member (Figure 1).
In jaw crushers, the material is crushed by pressing and bending and sometimes by abrasion between two rectangular plates or jaws that form a wedge-shaped working space. One jaw is usually stationary; the other is rocked by a drive mechanism. When the jaws come together, the material is crushed, and when the movable jaw moves away, the material falls from the machine. Jaw crushers were developed in the USA in 1858.
In cone crushers, which appeared in 1877, the crushing is done within a stationary conical bowl by a cone that performs a circular rocking (gyratory) motion. Where the cones come together, the material is crushed or broken by bending, and it falls out when the cone moves away. In cone crushers for primary crushing, the stationary conical bowl is mounted with the apex on the bottom, and the crusher cone is steep, with an angle of about 20° at the top. In cone crushers for secondary crushing and pulverization, the crusher bowl is mounted with the apex up; the cone is flat, the angle at the top is about 100°, and the annular discharge opening is large. Cone crushers for secondary crushing and pulverization were introduced in industry in the 1920’s. In roll crushers the material is pulled by forces of friction and crushed between two parallel cylindrical rolls rotating in opposite directions at the same speed. The rolls pull in a piece of material if the diameter of the roll is approximately 20 times greater than the size of the piece. Roll crushers appeared in England in 1806. Toothed roll crushers are used for brittle and soft materials such as coal and salt; they pull in pieces that are only 1.5-4 times smaller than the diameter of the roller. Hammer crushers, or hammer mills, crush material by blows from hammers that are mounted by hinges on a rapidly turning rotor (the tip speed of the hammers is up to 55 m/sec), and the pieces of material are also broken by blows against the plates of the mill. Such mills in their modern form were proposed by Williams (USA) in 1895. Rotary crushers use a massive, rapidly turning rotor with rigidly attached hammers and repeated blows of the pieces on the strike plates or screens. Such crushers were patented in the USA (1842) and used in the USA in 1939 and in Germany in 1942. Rod crushers (disintegrators) were invented in England in 1859. Crushers of the first three types are used to crush hard materials (ores and building stone); hammer breakers are used for brittle and soft materials (coal, limestones, and bauxites). The main characteristics of modern crushers are given in Table 1. The general features that are required in crushers are ease of unloading of materials and replacement of worn parts, protection against breakdowns when uncrushable objects enter the machines, and simplicity of regulation of the size of the product. Improvements in crushers are directed toward an increase in their size, the introduction of wear-resistant metals, and the use of hydraulic devices to guard against breakdowns and to control the size of the product. REFERENCESBerenov, D. I. Drobil’noe oborudovanie obogatitel’ nykh i drobil’nykh fabrik. Sverdlovsk, 1958.Barabashkin, V. P. Molotkovye i rotornye drobilki. Moscow, 1963. Bulychev, V. V., and V. E. Boldyrev. Novoe oborudovanie obogatitel’nykh fabrik. Moscow, 1967. V. A. PEROV Crushera machine for smashing the stems of sown herbaceous plants to facilitate drying. The crusher works independently or with a mounted mower. The basic working parts of the PTP-2.0 machine used in the USSR are the drum pickup with spring pins and two crusher rollers located one above the other. The upper roller can be moved in guides, depending on the thickness of the layer of stalks being taken in by the crusher. The lower roller has longitudinal grooves that improve the grip on the stalks. The upper roller is forced against the lower one by springs, the tension of which is adjusted for the type of plant to be processed. The productivity of the crusher is 1.4 hectares per hour; the operating width is 1.95 m. The working parts of the crusher are driven by the power takeoff shaft of the tractor. crusher[′krəsh·ər]crushercrushercrusher
Words related to crusher
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 随便看 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
英语词典包含2567994条英英释义在线翻译词条，基本涵盖了全部常用单词的英英翻译及用法，是英语学习的有利工具。
